Bay Networks 5391 Installationsanleitung PDF herunterladen (Seite 75)

3-17Remote Annex 6300 Hardware Installation Guide

Chapter 3 ROM Monitor Commands

If the self-boot option is not used, the command display looks like this:

WARNING

monitor:: erase

Erase all non-volatile EEPROM memory? (y/n) [n]:: y

Erasing 65504 bytes of non-volatile memory. Please

wait...

16K->|Data 0x0

.................................................

Initialized checksum record installed

Erasing 65504 bytes of non-volatile EEPROM memory

1 2 ... 70 71 72 73 74 75 76 77 78 79 80 ... 137 138

Remote Annex 1
Rules, Part 68 6
Revision Level History 7
Revision Level History 8
Contents 9
Contents 10
About this Guide 15
Printing Conventions 16
Preface 17
Convention: Represents: 17
Related Documents 18
Bay Networks Customer Service 19
World Wide Web 21
Customer Service FTP 22
Support Source CD 22
CompuServe 22
InfoFACTS 23
How to Get Help 24
Remote Network Access 25
Remote Annex 6300 Description 26
Main Logic Board 26
Modem Carrier Card 27
Firmware and Software 27
ROM Monitor 28
Supported 28
Conﬁgurations 28
Watchdog Timer 28
Front Panel 29
Front Panel Components 30
Network/Status 31
(continued on next page) 31
The button is used to: 32
Rear Panel 33
Rear Panel Components 34
Physical Characteristics 35
Before you Begin 37
Front Mount 38
(3 places each side) 39
Rear Mount 40
Bracket Mounting 41
(2 Screws each side) 41
Bracket Assembly 41
(2 Screws, 2 Nuts, and  41
4 Washers each side) 41
CONSOLE 10BASE5 10BASET 42
ISDN PRI 42
❑ Thin Ethernet (10Base2) 43
❑ Thick Ethernet (10Base5) 43
❑ Twisted Pair (10BaseT) 43
Ethernet cable (see 45
Figure 2-7): 45
Figure 2-8): 46
Connecting a Console Terminal 47
Annex 6300 49
2 Apply power 50
6300 to your LAN 53
This section describes: 53
3 Execute the boot command 54
BOOTP response with the sm 56
Invoking the Console Monitor 58
Command Descriptions 60
Command Description Use 62
Remote Annex 6300 is booted 72
Remote Annex’s console port 73
6300 ROM Monitor commands 76
Network test – PASSED 81
[data bytes] [npackets] 84
Statistic Description 87
Bay Networks 89
LED(s) Description 91
Power-up and Boot Procedures 92
N1: LEDs OK 93
N2: Hardware OK 93
NE2: Hardware Failure 94
NE5: Booted wrong image 94
Setup Mode 95
T1: Testing LEDs 96
T2: Testing Hardware 96
T3: At Monitor Prompt 96
TE2: Hardware Failure 97
TE7: Booted Wrong Image 97
Boot Failures 98
Boot Error Report 99
Error Description 100
The broadcast address 101
The subnet mask 101
# /etc/erpcd –D5 103
# boot -v 103
Another Remote Annex 6300 104
Remote Annex 6300 Dumps 105
Annex overwrites crash dumps 106
Console Port 109
10Base2 Ethernet Port 110
10Base5 Ethernet Port 111
10BaseT Ethernet Port 112
PRI ISDN Interface 113
Loopback Connectors 115
Contents of the Kit 117
Disassembly Instructions 118
Installation Instructions 119
Assembly Instructions 121
Power-up and Test 122
Removing Quad Modem Cards 131
Modem Card 133
DIP Switch S1 134
Front of Unit 134

Kommentare zu diesen Handbüchern

Keine Kommentare

Bay Networks 5391 Installationsanleitung Seite 75

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Software Bay Networks 5391